MENU
China Chamber of Commerce

Overseas Economic and Trade Zones

Confirm
Cancel
x

Ok
x
Sign into your account
Member ID or Email
Join Free
Home > > >
pruning shears li-ion battery pack (18V 5S1P)
pruning shears li-ion battery pack (18V 5S1P)

pruning shears li-ion battery pack (18V 5S1P)

Member Details

JIANGSU HIGHSTAR CREMICAL POWER SOURCE CO., LTD.

Nantong,Jiangsu,China

Trading Company,Manufacturer

  • Product Details
  • Company Profile

pruning shears li-ion battery pack (18V 5S1P)

Production specifications


Item 項目Description  內容Remark 備注
Rated capacity
額定容量		1300mAh0.2ItA discharging 放電
Rated capacity
額定電壓		18V
Charging method
充電方式		CC/CV 恒流/恒壓
Changing voltage
充電電壓		21.3V
Standard  discharging current
標準放電電流		13A
Max continuous discharging current
最大連續放電電流		20A5S
IR difference of grouping
配組內阻差		≤1mΩ
Operating working temperature
工作環境溫度		Charing 充電：0℃～40℃；
Discharging 放電：-10℃～60℃
Outgoing voltage
出廠電壓		≥18V


Electrical performance

 

Item 項目Test method 測試方法Criteria 判定標準
Standard charge
標準充電		Charge at CC mode at 260mA until the pack voltage reaches 21.3V, change to CV charge mode, when the charging current is no higher than 65mA, stop charging.
以260mA恒流充電，當電壓達到21.3V後，轉為恒壓充電，充電電流小於或等於65mA時，充電結束。
Rapid charge
快速充電		Charge at CC mode at 1300mA until the pack voltage reaches 21.3V, change to CV charge mode, when the charging current is no higher than 65mA, stop charging.
以1300mA恒流充電，當電壓達到21.3V後，轉為恒壓充電，充電電流小於或等於65mA時，充電結束。
Capacity
容量		Rest the battery for 1 hour after being fully charged by standard charging mode. Keep discharging the battery at current of 260mA until the cut-off is triggered.
標準充電後擱置1小時，以260mA電流連續放電至電池組放電保護。		Discharging time≥5hrs
放電時間≥5小時
Capacity measured at 10C discharge
10C放電容量		Rest the battery for 1 hour after being fully charged by standard charging mode. Keep discharging the battery at current of 13A until the cut-off is triggered.
快速充電後擱置1小時，以13A放電至電池組放電保護，		Discharging time≥5.4mins
放電時間≥5.4min
Cycle life
循環壽命		Leave the battery for 10 mins after rapid charged. Keep discharging the battery at current of 13A until the PCB protection is triggered. Rest the battery for 45 mins before the next charging/discharging cycle, until the battery discharging capacity are below 80% of the nominal capacity in continuous twice. The test is over.
快速電後擱置10min，以13A電流恒流放電至電池組受保護板過放保護無輸出，擱置45min，再進行下一個充放電循環，直至連續兩次放電容量低於額定容量的80%，試驗結束。		Cycle life is no less than 200 times
循環次數不低於200次

 

 


Other info




Send Inquiry to This Supplier

  • Title
  • From*
  • toCraign Gu
  • Message*
  • Minimum Order Quantity*
  • Unit
  • Verification Code*